Chassis
| Part# | Picture |
Description |
 |
Quickchange Rear Ends For Early Fords, complete kit featuring Winter's
components that use original axles, housings and carrier. All new
parts including assembly instructions, 4:11 Ring and pinion, 3:48 Final
gear set Notice: This is for closed drive |
|
 |
Quickchange Rear Ends For Early Fords, complete kit featuring Winter's
components that use original axles, housings and carrier. All new
parts including assembly instructions, 4:11 Ring and pinion, 3:48 Final
gear set Notice: This is for open drive |
|
 |
Torque Tube Driveshafts. For earlyford banjo rear end or quickchanges. Another neat part for your nostalgia hot rodder, a cut to length driveshaft for your cut-down torque tube banjo rear or your torque tube Quickchange.Fits 35-48 Ford V8's All new parts including assembly instructions, coupler fits any Ford 6 spline pinion or quickchange jackshaft. 10 spline adapter available, fits Ford U-joint, Uses stock speedometer drive gear, supplied with 60" tube that you cut to length | |
| 21c-3020 |  |
Front Axel Bumper Big trucks 1935-1936 |
| 48-5089 |  |
Engine Support 1935-1936 |
| 40-5089-B |  |
Engine Support Rear pass & commercial 1933-1934 |
| B-5089-B |  |
Engine Support Rear transmission mount 1932 |
| 48-3111 |  |
King Pin Spindle Bolt Set Complete w. all hardware. 1935-1936 |
| 78-3111 |  |
King Pin Spindle Bolt Complete w. all hardware 1937-1941 |
| X-3111 |  |
King Pin Repair Kit Kit includes all the parts, except the spindle bolts (kingpins) themselves. If your kingpins are good, but you need new bushings, bearings, felts, shims and hardware. Then order this kit. 1928-1941 |
| 91A-3020 |  |
Axle Bumper Front 1939-1940 |
| 51A-3020 |  |
Axle Bumper Front 1946-1948 |
| 78-3524 |  |
Steering Worm Gear Passenger & commercial 1937-1948 |
| B-3517-N |  |
Steering Column Rubber Bushing With brass insert 1932-1948 |
| 01A-3533-SPR |  |
Sway Bar Swivel Assembly 1940-1941 |
| 11A-3558 |  |
Sway Bar Bushing 1940-1941 |
| 18-4035-S |  |
Rear End Gasket Set 1932-1948 |
| 68-4209-HS |  |
Ring & Pinion All bearings, seals, and gaskets necessary to install your high speed ring and pinion are available online. 3:55:1 High speed. 35-48 Passenger & 35-41 PickUp, 1935-1948 |
| 40-4209-HS |  |
Ring & Pinion Gear 3:55:1 High speed. 1932-1934 |
| 48-4684 |  |
Spline Adapter 10x6 1935-1948 |
| B-4515-S |  |
Universal Joint Gasket 1932-1948 |
| 11A-3310 |  |
Tie Rod Coupling Sleeve 1935-1965 |
| xxx-3270 |  |
Tie Rod End Right & Left 1935-1959 |
| 51A-1139 |  |
Hub Dust Cap Front, press on 1945-1948 |
| 68-1139.jpg |  |
Hub Dust Cap Front, threaded style 1935-1946 |
 |
Spindle Nuts & Washers Spindle nuts & washers fits '28-'48 Ford and Magnum spindles. |