NY STROMBERG 97

The new, re-issue 97 is built accurately to original blueprint specification, with a few key improvements. And early dyno tests have proved that it matches or exceeds original spec.

LAGERVARE

PREMIUM JET WRENCH

Stainless steel with knurls for good grip and a CNC milled end for a super fit. Cheaper wrenches have a punched end. This will last a lifetime.

9071K

 SUPERSEAT HOSE FITTING

The only one available with the correct 18 degree seat for Stromberg inlet fittings (original or S-jet). So no leaks and period looks too. Big 9/16” AF hex cost us more to make but looks right on the hose. Made for 5/16” ID hose – but 3/8” ID clamps up OK.

9080K

PREMIUM SERVICE KIT STROMBERG 97,48 AND 40

Full gasket kit, ‘No-stick’ S-jet inlet valve, Accelerator pump check valve, 2 idle mixture screws and springs, Full accelerator pump kit, Installation sheet and float gauge

9590K-97 

PREMIUM SERVICE KIT FOR STROMBERG 81

Full gasket kit, ‘No-stick’ S-jet inlet valve, Accelerator pump check valve, 2 idle mixture screws and springs, full 81-size accelerator pump kit, installation sheet and float gauge

9590K-81

FULL GASKET KIT

three main gaskets,plus felt gasket for accelerator pump, and ring gaskets for power jet, inlet valve and drain plugs 

9447K

CARB TO MANIFOLD GASKET

pack. 6 gaskets 

69447K

ACCELERATOR PUMP ROD

for 97 and 81 - stainless steel 

9526K-97

ACCELERATOR PUMP ROD

for 40 and 48 - stainless steel 

9526K-48

MAIN JETS

pair  - all sizes available

9533K-size 

EMULSION TUBES

Pair.

9534K

IDLE ADJUSTING SCREWS & SPRINGS

Pair

9541K

IDLE JETS

Pair.

9542K

FLOAT PIN

9558K

BOWL PLUG GASKETS

(pack of 10) 

9563K 

FUEL INLET

S-jet with gasket

9564K

ACCELERATOR PUMP CHECK VALVE

......Thats it....

9573K 

THROTTLE/CHOKE PLATE SCREW KIT

 pack of 10 

9586K 

POWER BY-PASS JET

with gasket - all sizes available 

9594K-size

ACCELERATOR PUMP KIT

inc. springs/retainers/washers/felt gasket/cotter pin 

9630K

ACCELERATOR PUMP

stainless steel rod

9631K

ACCELERATOR PUMP

for the Stromberg 8,1with correct 10-finger brass spring washer beneath a leather seal

9631K-81

BOWL PLUG KIT

all 3 plugs with gaskets 

9522K 

BOWL GALLERY PLUGS

(pack of 20)

9523K

ACCELERATOR PUMP LEVER

Inc, spring & cotter pin - stainless steel 

9531K

CHOKE LEVER DETENT

plunger & spring - stainless steel 

9537K

CHOKE LOCK DETENT KIT

Most Strombergs – even in multiples - run better with the choke plates in. But who needs rattling levers? Lock them open with this clever detent plunger.

9537K-L

CHOKE SHAFT KIT

inc. lever, washer, screw & end stud 

9546K

CHOKE PLATE KIT

inc. screws - stainless steel plate with correct 15 deg edge 

9549K 

STROMBERG SUPERFLOAT™

Brass float. Made on the original Stromberg vendor tooling. And supplied with a new float pin.

9550K

CHOKE KICKER ASSEMBLY

Choke kicker assembly (stainless steel) inc. idle screw & spring

9552K

CHOCKE KICKER ASSEMBLY

model 97 choke kicker assembly for cable choke (designed for '49-on Fords). A separate bracket - included - mounts off the rear body screw to hold the cable sleeve.

9552K-C

SPRING KIT

all exterior springs - all stainless except idle adjuster springs 

9571K

ACCELERATOR PUMP DISCHARGE JET PLUS COLLAR

- pair

9577K

THROTTLE SHAFT AND LEVER KIT

Throttle shaft and lever kit inc. screws & bushes -

stock size

9581K

THROTTLE PLATE

7 degree edge - pair

9585K

 THROTTLE STOP SCREW

Throttle stop screw & spring - stainless steel

9589K

CHOKE & ACCELERATOR  SCREWS 

pump lever fulcrum screws both stainless steel

9592K 

CARB BLANK OFF PLATE

Want to keep a carb or two out of action? Slip this thin stainless plate between the carb and gasket.

29447K

BODY SCREW KIT

 8 screws/washers - stainless steel

31095K 

MANIFOLD STUD KIT

3 studs with stainless lock washers and nuts 

89067K-3

MANIFOLD STUD KIT

4 studs with stainless lock washers and nuts 

89067K-4